oneshot 45 Posted August 27, 2014 I'll try to keep this short and sweet. I had some 30 round Ar mags that I brought to a FFL gunshop/range/gunsmith to be modified to hold the NJ leagal 15 rounds. waited 3 months. Apparently they are no longer allowed to use rivets to reduce the round limit yet if it comes from the factory like that it's ok. I was told NJ state police came up with this. So is there anything on the books about this? If it is true, i do not understand why its any different whether its done by the factory or a FFL. If someone wanted to buy 30 rounders it's not that difficult. Why would you go through the trouble of buying blocked mags and then make them illegal?!?! Quote Share this post Link to post Share on other sites
PK90 3,573 Posted August 27, 2014 The dealer does not want to be bothered permanently altering them to 15 rounds and made that up. Have them send them to me. I will convert them and send them directly back yo you. Quote Share this post Link to post Share on other sites
JT Custom Guns 958 Posted August 27, 2014 I too have heard (in the past) from NJ state police members that they do no accept rivets, but there is nothing written and the law is very vague as to how the block the mag(s) so some people are very leary about how to do it. [Large Capacity means a box, drum, tube or other container, which is capable of holding more than 15 rounds of ammunition to be fed continuously and directly therefrom into a semi-automatic firearm. A large capacity ammunition magazine that has been permanently altered so that it is not capable of holding more than 15 rounds of ammunition will cease to be defined as a "large capacity ammunition magazine." An ammunition magazine, which has been temporarily blocked or modified from holding more than 15 rounds, as by a piece of wood or a pin, is still considered to be a "large capacity ammunition magazine.] Now some people confuse the "pin" as the pin that seals the mag - I read it as a pin or block of wood that is placed into the mag and can be easily removed (temporary) when the mag is opened (this is why so many people insist the mags have to be sealed, even though the law says nothing about sealing them) Personally, I don't use rivets, I remove the floor plate and weld a bolt that is long enough to prevent the follower from coming down far enough to allow no more than 15 rounds. Some mags have (S&W M&P 9 for example) have plastic floor plates so they cant be welded. P-Mags cant be welded. In these cases, a replacement block can be used that replaces the original parts of the mag and then the mag seals so it cant be removed. This is different than sticking a pin or block of wood inside a mag because if you remove the modified bloc them mag will no work; the mag is being modified, not just blocked. Paul (PK90) is good at doing mags commercially (I only modify for the guns I sell) so I recommend you taking him up on his offer. Good Luck! JT Quote Share this post Link to post Share on other sites
Howard 538 Posted August 27, 2014 I talked to my FFL about this a while ago as they would routinely put a rivet in Glock mags to make them 15 rounds. They had previously been told by the state police that this was fine. During the last campaign to further neuter our mags they approached the state police about retrofitting existing 15 round mags to 10 rounds and were told they could do that but the police would no longer accept the rivet method. They told them they had no problem with the existing ones out there, but did not want that done anymore. Well since mags are not serialized or date stamped this makes absolutely no sense - how would someone determine when a mag had been altered. The laws in this state are so screwed up. Quote Share this post Link to post Share on other sites
MidwestPX 172 Posted August 27, 2014 I too have heard (in the past) from NJ state police members that they do no accept rivets, but there is nothing written and the law is very vague as to how the block the mag(s) so some people are very leary about how to do it. [Large Capacity means a box, drum, tube or other container, which is capable of holding more than 15 rounds of ammunition to be fed continuously and directly therefrom into a semi-automatic firearm. A large capacity ammunition magazine that has been permanently altered so that it is not capable of holding more than 15 rounds of ammunition will cease to be defined as a "large capacity ammunition magazine." An ammunition magazine, which has been temporarily blocked or modified from holding more than 15 rounds, as by a piece of wood or a pin, is still considered to be a "large capacity ammunition magazine.] Now some people confuse the "pin" as the pin that seals the mag - I read it as a pin or block of wood that is placed into the mag and can be easily removed (temporary) when the mag is opened (this is why so many people insist the mags have to be sealed, even though the law says nothing about sealing them) Personally, I don't use rivets, I remove the floor plate and weld a bolt that is long enough to prevent the follower from coming down far enough to allow no more than 15 rounds. Some mags have (S&W M&P 9 for example) have plastic floor plates so they cant be welded. P-Mags cant be welded. In these cases, a replacement block can be used that replaces the original parts of the mag and then the mag seals so it cant be removed. This is different than sticking a pin or block of wood inside a mag because if you remove the modified bloc them mag will no work; the mag is being modified, not just blocked. Paul (PK90) is good at doing mags commercially (I only modify for the guns I sell) so I recommend you taking him up on his offer. Good Luck! JT Plastic can be welded. The cost of the machine is significantly higher. The one we use for PMAGs cost in excess of $10K. Quote Share this post Link to post Share on other sites
djg0770 481 Posted August 27, 2014 Some mags have (S&W M&P 9 for example) have plastic floor plates so they cant be welded. Sure they can - http://en.wikipedia.org/wiki/Ultrasonic_welding Quote Share this post Link to post Share on other sites
oneshot 45 Posted August 27, 2014 Yeah Howard I'm calling BS on this. Because if it's ok for the manufacture to ship them this way then there is no reason why an FFL can't do it the exact same way and be in compliance. I'm going with what PK said because they are selling his and they have rivets in them. And if i'm not mistaken PK is an FFL not a manufacturer of firearms. The glock 17 mags are also riveted. Quote Share this post Link to post Share on other sites
remixer 1,645 Posted August 27, 2014 What manufacture ships a factory round with a rivet to limit capacity. Quote Share this post Link to post Share on other sites
oneshot 45 Posted August 27, 2014 What manufacture ships a factory round with a rivet to limit capacity. You know what thats a good frigging question!!!Im going on what they told me. So its definitely bullshit. They are selling pinned G17 mags that they riveted and PK's 15 round AR mags that are riveted.. bamboozled Quote Share this post Link to post Share on other sites
MidwestPX 172 Posted August 27, 2014 What manufacture ships a factory round with a rivet to limit capacity.LWRC Quote Share this post Link to post Share on other sites
remixer 1,645 Posted August 27, 2014 Interesting Quote Share this post Link to post Share on other sites
MidwestPX 172 Posted August 27, 2014 Interesting I should clarify that they were making 10/20s before there were 10rd body PMAGs available. I don't know if they ever a) made a 15/20 with a rivet and b) shipped such a 15/20 to NJ. Quote Share this post Link to post Share on other sites
jackandjill 683 Posted August 28, 2014 windham weaponry once (within last year) sent me a 15 rnd magazine riveted to 10. go figure. Quote Share this post Link to post Share on other sites