Let see those Rimfires. =P

[dgstinner 11]

I purchased a Smith & Wesson M&P 15-22 from Bullseye Tactical last weekend.

[papercutninja 24]

S&W M&P22 12-rd mag. Just picked it up on Friday. First thing i did was remove that ridiculous thumb safety, as it was hindering a proper grip for me. Next, i have to go shoot it.

 

[Qel Hoth 33]

Could you post how you did this or directions that you used? I am considering this as well, especially if I decide to purchase an M&P 9 that does not have the thumb safety.

[papercutninja 24]

The M&P22 has a metal "chassis" that sits in the polymer frame.

 

1. Grab a punch and knock out the roll pins. I've heard that you can wiggle the safeties off just by removing the rear pin, but i wasn't able to get that to work.

2. Once both pins are out, the chassis lifts right out, and the only thing left in the frame is the mag release and mainspring. There is a bit of pressure from the mainspring pushing the whole assembly up, but no small parts will fall off.

3. The plastic safety levers are attached to square posts, and pull straight off.

4. When putting the chassis back in the frame, just make sure that the safety is down. If you install it with the safety up, you can push it down with a thin bladed screwdriver.

 

The trickiest part to getting it all back together is getting the hammer strut to sit on the mainspring cap without slipping off. Other than that, it's a 5 minute job.

[fumanchu182 23]

Not sure if I posted these before...

 

[mintbore 15]

Cuda stock

Whistle Pig Barrel

Volq Innards, bolt handle and mag release

 

[this_is_nascar 162]

My small current collection.

 

 

Beretta Series 92 Pratice Kit:

 

 

Ruger 10/22 for the Mrs:

 

 

Ruger 10/22 for Me:

 

 

Ruger Mark III:

 

 

Taurus 94 5":

 

 

Marlin XT-22TSR:

 

 

Colt-Umarex 1911 Rail .22LR:

[Scrap 4]

 

 

 

 

 

[the_stranger 13]

Rifles

 

CZ-452 Ultra Lux

 

 

 

CZ-452-FS

 

 

 

Henry Golden Boy

 

 

NC-22 Upper / Spike's Lower

[the_stranger 13]

Ruger 22/45

 

 

 

Ruger Single Six Convertible

[Shortfuse 39]

Savage Model 3D - Mossberg Tactical

[Jmac92 0]

My .17 HMR Woodchuck slayer

 

 

 

Nice rifle!! What scope do you have on there?

[Lalo 13]

Sig Mosquito

 

S&W 15-22

[JonF 79]

My ultra light AR-22. She's a svelte 3# even with optics due to its minimalistic design and extensive use of carbon fiber and polymer (the only steel is in the barrel liner and bolt/trigger).

 

[Scrap 4]

 

 

 

 

 

[BMWR12 35]

My Brand new ATI STG44 fresh out of the wood box.

[Scrap 4]

THAT my friend is very very nice- a classic classic firearm.

 

I'd like a few more myself.... can never EVER have too many .22LR's..

[KramD52 0]

Just when I thought that I had enough 22LR's in the houshold, someone has to go and post a pic of the STG44. Damn, thats nice.

[Steve_G 51]

Sig 1911-22

 

 

.22LR AR-15 NJGF Lower

 

[Bully 749]

My ultra light AR-22. She's a svelte 3# even with optics due to its minimalistic design and extensive use of carbon fiber and polymer (the only steel is in the barrel liner and bolt/trigger).

 

 

With the inherent understanding that more steel would have to be used in a centerfire caliber, can something like this be built for a centerfire? Very cool looking. Where did you find the parts for it?

 

C

[JonF 79]

With the inherent understanding that more steel would have to be used in a centerfire caliber, can something like this be built for a centerfire? Very cool looking. Where did you find the parts for it?

 

C

The answer is yes, however, it is significantly more expensive for centerfire the ligher you wish to go.

 

On the cheap end of the spectrum, there are factory offerings from the likes of Bushmaster (Carbon-15) who employ polymer upper and lower receivers and lighweight profile barrels to keep the weight down. The net result is a very light rifle but many people question the fragility and durability of that brand. Then there are the homebrew equivalents using NFA/plum crazy, CAV arms, etc receivers with a polymer upper (bushmaster or worse, vulcan) and lightweight carbine or ACE stocks with 14.5" pencil barrels and plastic/carbon fiber handguards which can result in sub 5lb centerfire configurations. On the exotic end of the spectrum, you have Christiansen Arms who builds something similar to mine above in 223 but at a very high cost. They have a carbon fiber sleeved bull barrel to save weight which provides for better accuracy than a simple minimalistic pencil barrel. They do use aluminum receivers but to haev carbon fiber handguards to keep front end weight down so the balance, which is the most important factor, is still good even if its not the absolute lightest.

[this_is_nascar 162]

My Brand new ATI STG44 fresh out of the wood box.

 

 

I really like that.

[Bully 749]

The answer is yes, however, it is significantly more expensive for centerfire the ligher you wish to go.

 

On the cheap end of the spectrum, there are factory offerings from the likes of Bushmaster (Carbon-15) who employ polymer upper and lower receivers and lighweight profile barrels to keep the weight down. The net result is a very light rifle but many people question the fragility and durability of that brand. Then there are the homebrew equivalents using NFA/plum crazy, CAV arms, etc receivers with a polymer upper (bushmaster or worse, vulcan) and lightweight carbine or ACE stocks with 14.5" pencil barrels and plastic/carbon fiber handguards which can result in sub 5lb centerfire configurations. On the exotic end of the spectrum, you have Christiansen Arms who builds something similar to mine above in 223 but at a very high cost. They have a carbon fiber sleeved bull barrel to save weight which provides for better accuracy than a simple minimalistic pencil barrel. They do use aluminum receivers but to haev carbon fiber handguards to keep front end weight down so the balance, which is the most important factor, is still good even if its not the absolute lightest.

 

Hey Jon, thanks. Where did you find the parts for yours?

 

C

[Shawnmoore81 623]

 

Savage .17hmr with sweet 17 scope and bipod.

[JonF 79]

Hey Jon, thanks. Where did you find the parts for yours?

 

C

 

Chris, TACCOM makes the complete upper (carbon barrel, receiver and handguard) and also the carbon butstock. They also sell bolts now but i have a stainless CMMG bolt. Lower receiver is polymer NFA from joebob's.

 

http://www.taccom3g.com/AR15_22LR_COMPONENTS.html

[Bully 749]

Thanks, Jon. Much appreciated.

 

C

[tony357 386]

mossberg 22lr tactical.

 

 

 

[Purple Patrick 638]

Here's my custom built ar with the cmmg conversion and the new red dot I got for Xmas

[Purple Patrick 638]

Better pic

[Scrap 4]

Very nice, obviously it looks like a real deal AR... would easily mistake it for a .223 buddy (In a good way I mean.)